HP ProLiant DL60 Gen9 User Manual Download Page 80

Page: 80 / 127

Cabling 80

Cabling

Cabling overview

This section provides guidelines that help you make informed decisions about cabling the server and

hardware options to optimize performance.
For information on cabling peripheral components, refer to the white paper on high-density deployment at

the Hewlett Packard Enterprise website (

http://www.hpe.com/info/servers

CAUTION:

When routing cables, always be sure that the cables are not in a position where

they can be pinched or crimped.

Storage cabling

Depending on the controller option installed, the actual storage controller connectors might look different

from what is shown in this section.

Four-bay LFF non-hot-plug drive cabling

•

Four-bay LFF non-hot-plug drive backplane connected to the system board

Item

Description

Drive power cable

Mini-SAS cable

Summary of Contents for ProLiant DL60 Gen9
































































































































Search results

Summary of Contents for ProLiant DL60 Gen9

Reviews:

Related manuals for ProLiant DL60 Gen9

Brands by name

Popular brands

HP ProLiant DL60 Gen9, User Manual

Search results

Summary of Contents for ProLiant DL60 Gen9

Reviews:

Related manuals for ProLiant DL60 Gen9

Brands by name

Popular brands