HP ProLiant DL60 Gen9 User Manual Download Page 47

Page: 47 / 127

Hardware options installation 47

Fan population guidelines

Configuration Fan bay

Fan bay

One processor,

non-redundant

Fan

Blank

Fan

Blank

One processor,

redundant

Fan

Blank

Two processors,

non-redundant

Fan

Blank

Fan

Blank

Fan

Two processors,

redundant

Fan

•

In the redundant fan mode:

If one fan rotor fails, the system continues to operate without redundancy. This condition is

indicated by a flashing amber Health LED.

If two fan rotors fail, the operating system shuts down.

Installing a hot-swap fan module

WARNING:

To reduce the risk of personal injury from hot surfaces, allow the drives and the

internal system components to cool before touching them.

To install the component:

Power down the server (on page

Remove all power:

Disconnect each power cord from the power source.

Disconnect each power cord from the server.

Do one of the following:

Extend the server from the rack (on page

Remove the server from the rack (on page

Remove the access panel (on page

Remove the air baffle (on page

Summary of Contents for ProLiant DL60 Gen9
































































































































Search results

Summary of Contents for ProLiant DL60 Gen9

Reviews:

Related manuals for ProLiant DL60 Gen9

Brands by name

Popular brands

HP ProLiant DL60 Gen9, User Manual

Search results

Summary of Contents for ProLiant DL60 Gen9

Reviews:

Related manuals for ProLiant DL60 Gen9

Brands by name

Popular brands