HP integrity rx2800 i4 User Manual Download Page 144

Page: 144 / 156

Table 45 UEFI shell commands

(continued)

Definition

UEFI shell command

Resets the system

reset

Deletes one or more files or directories

Make a SAL procedure call

salproc

Connect drivers for bootable devices

View/configure system security features

secconfig

Sets serial port attributes

sermode

Displays or modifies UEFI Shell environment variables

set

Set the size of a file

setsize

Shifts batch file input parameter positions

shift

Displays SMBIOS information

smbiosview

Stalls the processor for the specified number of microseconds

stall

Boot from tape

tapeboot

Perform TFTP operation

tftp

Displays or changes the current system time

time

Displays or sets time zone information

timezone

Updates filename timestamp with current system date and time

touch

Displays file contents

type

Unloads a UEFI driver

unload

Displays UEFI Firmware version information

ver

Displays or changes a file system volume label

vol

Turn on/off extended character features

xchar

Drive paths in UEFI

Devices in the server are represented by device paths in the UEFI shell. Each internal SAS drive
could be configured either as:

•

RAID mode

•

HBA (raw) mode

NOTE:

A SAS drive in RAID mode is identified by "Scsi" in the device path A SAS drive in HBA

mode is identified by "SAS" in the device path.

NOTE:

Unlike parallel SCSI, you cannot correlate UEFI device paths to internal SAS disk drive

bays with SAS regardless of RAID/HBA mode. The UEFI device paths currently do not contain any
information that could be used to determine the physical location of the drives.

Path example

Path format

Device

PcieRoot(0x30304352)/Pci(0x2,0x0)/
Pci(0x0,0x0)/Scsi(0x0,0x0)

UID

PCIe root bridge device path
node

(RAID mode)

PcieRoot(0x30304352)/Pci(0x2,0x0)/Pci(0x0,0x0)
/SAS(0x5000C500037688B9,0x0,0x1,NoTopology,
0,0,0,0x0)

HP Confidential

144 Utilities

Summary of Contents for integrity rx2800 i4





























































































































































Search results

Summary of Contents for integrity rx2800 i4

Reviews:

Brands by name

Popular brands

HP integrity rx2800 i4, User Manual

Search results

Summary of Contents for integrity rx2800 i4

Reviews:

Brands by name

Popular brands