HP FlexFabric 7900 Series Command Reference Manual Download Page 184

Page: 184 / 294

176

Table 23 Command output

Field Description

ISSU state

ISSU status:

•

Init

—The ISSU process has not started or has finished.

•

—The system is executing the

issu load

command.

•

Loaded

—The

issu load

command is completed.

•

Switching

—The system is executing the

issu run switchover

command.

•

Switchover

—The

issu run switchover

command is completed.

•

Accepted

—The

issu accept

command is completed.

•

Committing

—The system is executing the

issu commit

command.

•

Rollbacking

—A rollback is going on.

•

Unknown

—An upgrade is going on. This field might appear when you execute

the command on an original standby MPU.

Compatibility

Version compatibility

•

Incompatible

•

compatible

•

Unknown

This field displays

Unknown

if no upgrade is going on.

Work state

Operating state of the device:

•

Normal

—The device is operating correctly.

•

Independent active

—When you perform an ISSU for an incompatible version, the

standby MPU that is upgraded first enters this mode. In this mode, the two MPUs
of the device are running different software versions.

Upgrade method

Upgrade mode. The upgrade mode is always card by card. On a two-chassis IRF
fabric, you must upgrade the subordinate first, and then the master.

Upgraded slot

Upgraded cards.

During a rollback, this field displays

Unknown

Upgraded chassis

Upgraded members.

Current upgrading
chassis

Members that are being upgraded.

Previous version
list

Software versions running on the device before the ISSU.

If you execute this command on an original standby MPU during an ISSU for an
incompatible version, the value of this field is

Unknown

Previous software
images

Software images running on the device before the ISSU.

If you execute this command on an original standby MPU during an ISSU for an
incompatible version, the value of this field is

Unknown

Upgrade version
list

Software versions to upgrade to.

If you execute this command on an original standby MPU during an ISSU for an
incompatible version, the value of this field is

Unknown

Upgrade software
images

Software images used for the upgrade.

If you execute this command on an original standby MPU during an ISSU for an
incompatible version, the value of this field is

Unknown

Related commands

issu load

issu run switchover

Summary of Contents for FlexFabric 7900 Series







































































































































































































































































































Search results

Summary of Contents for FlexFabric 7900 Series

Reviews:

Related manuals for FlexFabric 7900 Series

Brands by name

Popular brands

HP FlexFabric 7900 Series, Command Reference Manual

Search results

Summary of Contents for FlexFabric 7900 Series

Reviews:

Related manuals for FlexFabric 7900 Series

Brands by name

Popular brands