HP Compaq Presario F500 - Notebook PC Maintenance And Service Manual Download

Page: 28 / 120

Removal and replacement
procedures

Preliminary replacement requirements

Tools required

You will need the following tools to complete the removal and replacement procedures:

●

Flat-bladed screwdriver

●

Hex 5.0-mm nutdriver

●

Magnetic screwdriver

●

Phillips P0 and P1 screwdrivers

Service considerations

The following sections include some of the considerations that you should keep in mind during disassembly
and assembly procedures.

NOTE:

As you remove each subassembly from the computer, place the subassembly (and all

accompanying screws) away from the work area to prevent damage.

Plastic parts

Using excessive force during disassembly and reassembly can damage plastic parts. Use care when
handling the plastic parts. Apply pressure only at the points designated in the maintenance instructions.

Chapter

Removal and replacement procedures

Summary of Contents for Presario F500 - Notebook PC

























































































































Search results

Summary of Contents for Presario F500 - Notebook PC

Reviews:

Related manuals for Presario F500 - Notebook PC

Brands by name

Popular brands

HP Compaq Presario F500 - Notebook PC, Maintenance And Service Manual

Search results

Summary of Contents for Presario F500 - Notebook PC

Reviews:

Related manuals for Presario F500 - Notebook PC

Brands by name

Popular brands