HP Compaq Presario F500 - Notebook PC Maintenance And Service Manual Download Page 50

Page: 50 / 120

Remove the display assembly

(2)

If it is necessary to replace any of the display assembly internal components, remove the eight rubber
screw covers from the display bezel:

NOTE:

There are three different sizes of rubber screw covers on the display bezel.

(1)

Four covers on the top edge of the bezel

(2)

Two covers on the lower bezel corners

(3)

Two covers on the lower-inside edge of the bezel

The display bezel rubber screw covers are included in the Display Screw Kit, spare part number
431400-001.

Chapter

Removal and replacement procedures

Summary of Contents for Presario F500 - Notebook PC

























































































































Search results

Summary of Contents for Presario F500 - Notebook PC

Reviews:

Related manuals for Presario F500 - Notebook PC

Brands by name

Popular brands

HP Compaq Presario F500 - Notebook PC, Maintenance And Service Manual

Search results

Summary of Contents for Presario F500 - Notebook PC

Reviews:

Related manuals for Presario F500 - Notebook PC

Brands by name

Popular brands