Hoshizaki FH1-SSB(-HD) Service Manual Download

Page: 24 / 100

b) Freezer

Defrost timer terminates

Legend:
Comp

-compressor

ConFM

-condenser fan motor

CTh

-cabinet thermistor

-display board

-defrost heater

DTh-

defrost thermistor

EvapFM

-evaporator fan motor

2. Cool Down

3. Cool Down Achieved

Comp

energized

ConFM

energized

EvapFM

energized

CTh in control

2.5 min.
Comp Delay

CTh cools
to 3°F (1.7°C)
below setpoint

CTh w

to 3°F (1

.7°C)

abo

ve setpoint

5. Defrost

EvapFM

energized

(if dip switch 7 or 8 on)

Comp

de-energized

ConFM

de-energized

EvapFM

de-energized

(if dip switch 7 and 8 off)

DTh warms to
100°F (38°C)

Note:

• 2.5-minute minimum compressor on and off time.
• Evaporator fan motor de-energizes when door is open.
• 20-minute minimum defrost time.
• 1-hour maximum defrost time.
• Perimeter heater controlled by perimeter heater switch

(except RFH1-SSB(-HS)(-HSE)).

• Glass door (-GD models) heater controlled by glass door

heater switch.

• RFH1-SSB(-HS)(-HSE): Perimeter heater and mullion heater

are controlled through the control board and turn on and off
with compressor when S3 dip switch 8 is in the off position.

• Models may utilize any combination of the following heaters:

Condensate Pan Heater, Cord Heater, Drain Heater, Duct

Heater, and Glass Tube Heater. See "VII.Wiring Diagrams"

for specific model details.

DTh in control

energized

Comp

de-energized

ConFM

de-energized

EvapFM

de-energized

EvapFM

energized

(if dip switch 7 or 8 on)

2.5-min. Comp
on timer starts

4. Cool Down Restart

de-energized

5-min. delay timer starts
after defrost heater
de-energizes

6. Cabinet Cool Down Defrost Recovery (Drip Time)

to 6 below

from 5 above

Comp

energized

ConFM

energized

Evaporator temperature
drops below 70°F (21°C)

Display changes from "dEF"

on DB to cabinet temperature
when CTh drops to 15°F
(8.3°C) or less above setpoint.

To 2 above

2.5-min. Comp off
timer starts

"RI-A" Control Board

Freezer Sequence Flow Chart

Comp

energized

ConFM

energized

EvapFM

energized

DTh at or above
100°F (38°C)

1. Startup

from 6 below

de-energized

Summary of Contents for FH1-SSB(-HD)





































































































Search results

Summary of Contents for FH1-SSB(-HD)

Reviews:

Related manuals for FH1-SSB(-HD)

Brands by name

Popular brands

Hoshizaki FH1-SSB(-HD), Service Manual

Search results

Summary of Contents for FH1-SSB(-HD)

Reviews:

Related manuals for FH1-SSB(-HD)

Brands by name

Popular brands