Hoshizaki FH1-SSB(-HD) Service Manual Download Page 61

Page: 61 / 100

D. Removal and Replacement of Heat Shield on FH2-SSB(-HD)

The heat shield was added to the evaporator assembly at auxiliary code M6. To replace
the shield, follow the instructions below.

1) Remove the original heat shield by lifting the evaporator up and sliding the heat shield

out.

2) Install the new heat shield in the rotocast drain pan.
3) Slide the clips onto the end plate on the evaporator. Install the two Support Clip (C) clips

onto the hairpin end of the evaporator as shown in the illustration.

4) Install Support Clip (A) and Support Clip (B) onto the return bend end (same side as

inlet and outlet tubes) as shown in the illustration.

Note: All clips are shown in the illustration in the correct orientation for installation. Slide

the parts onto the evaporator brackets using the tabs on the support clips.

Heat Shield

Support Clip (C)

Support Clip (B)

Support Clip (A)

Evaporator
Bracket

Summary of Contents for FH1-SSB(-HD)





































































































Search results

Summary of Contents for FH1-SSB(-HD)

Reviews:

Related manuals for FH1-SSB(-HD)

Brands by name

Popular brands

Hoshizaki FH1-SSB(-HD), Service Manual

Search results

Summary of Contents for FH1-SSB(-HD)

Reviews:

Related manuals for FH1-SSB(-HD)

Brands by name

Popular brands