Hoshizaki FH1-SSB(-HD) Service Manual Download Page 56

Page: 56 / 100

Appliance Not Cooling - Possible Cause

14. Compressor Relay

a) Bad contacts.
b) Open coil windings.

15. Compressor Protector

a) Dirty condenser.
b) Condenser fan not operating.
c) Defective.

16. Start Relay

a) Defective

17. Start Capacitor

a) Defective.

18. Compressor

a) Defective.

19. Condenser

a) Dirty.

20. Evaporator

See "2. Evaporator Frozen Up."

a) Dirty or frozen.

21. Refrigerant/Refrigerant Lines

a) Gas leak.
b) Refrigerant lines restricted.

22. Backup Defrost Thermostat

a) Stuck open/defective.

23. Defrost

See "3. Defrost Fails to Terminate" below.

2. Evaporator Frozen Up

Evaporator is Frozen Up - Possible Cause

1. Defrost Frequency

Not enough defrost occurring per day. See "II.E.1.b) Defrost Frequency."

2. Evaporator

a) Dirty.

3. Evaporator Fan Motor

a) Defective.
b) Fan Blade Binding.

4. Control Board

a) Defective.

5. Refrigerant Charge

a) Low.

6. Thermostatic Expansion Valve

a) Defective.

7. Defrost Thermistor (Freezer Only)

a) Out of position or defective.

8. Defrost Heater (Freezer Only)

a) Defective.

9. Drain Line

a) Restricted.

10. Defrost Drain Heater (Freezer Only

Auxiliary Code P-6 and Later)

a) Defective.

3. Defrost Fails to Terminate

Defrost Fails to Terminate - Possible Cause

1. Defrost Thermistor

Out of position or defective. See "III.C. Thermistor Check."

2. Control Board

a) Defective.

4. Other

Abnormal Noise - Possible Cause

1. Fan Blade (evaporator or

condenser)

a) Loose.

2. Fan Motor (evaporator or

condenser)

a) Defective.

3. Compressor

a) Defective.

Summary of Contents for FH1-SSB(-HD)





































































































Search results

Summary of Contents for FH1-SSB(-HD)

Reviews:

Related manuals for FH1-SSB(-HD)

Brands by name

Popular brands

Hoshizaki FH1-SSB(-HD), Service Manual

Search results

Summary of Contents for FH1-SSB(-HD)

Reviews:

Related manuals for FH1-SSB(-HD)

Brands by name

Popular brands