manualshive.com logo in svg

Hoshizaki FH1-SSB(-HD), Service Manual, Page: 6 / 100

Share
Download
Hoshizaki FH1-SSB(-HD) Service Manual Download Page 6

6

Important Safety Information

Throughout this manual, notices appear to bring your attention to situations which could 
result in death, serious injury, or damage to the appliance or damage to property. 

 WARNING  

Indicates a hazardous situation which could result in death or 
serious injury. 

NOTICE

 

Indicates a situation which could result in damage to the 
appliance or property.

IMPORTANT

 

Indicates important information about the use and care of the 
appliance.

 WARNING

This appliance should be destined only to the use for which it has been expressly 
conceived. Any other use should be considered improper and therefore dangerous. 
The manufacturer cannot be held responsible for injury or damage resulting from 
improper, incorrect, and unreasonable use. Failure to service and maintain the 
appliance in accordance with this manual will adversely affect safety, performance, 
component life, and warranty coverage.

To reduce the risk of death, electric shock, serious injury, or fire, follow basic 
precautions including the following:

• Only qualified service technicians should install and service this appliance.
• This appliance must be installed in accordance with applicable national, state, and 

local codes and regulations.

For Power Cord Models

• This appliance requires an independent power supply of proper capacity. See 

the nameplate for electrical specifications. Failure to use an independent power 
supply of proper capacity can result in a tripped breaker, blown fuse, or damage 
to existing wiring. This could lead to heat generation or fire.

• To reduce the risk of electric shock, do not touch the plug or power switch with 

damp hands.

• Make sure the power switch is in the "OFF" position before plugging in or 

unplugging the appliance to reduce the risk of electric shock.

• Before servicing, move the power switch to the "OFF" position. Unplug the 

appliance from the electrical outlet.

• Do not use an extension cord.
• Do not use an appliance with a damaged power cord. The power cord should not 

be altered, jerked, bundled, weighed down, pinched, or tangled. Such actions 
could result in electric shock or fire. To unplug the appliance, be sure to pull the 
plug, not the cord, and do not jerk the cord.

Summary of Contents for FH1-SSB(-HD)





































































































Reviews:

No comments