Hoshizaki FH1-SSB(-HD) Service Manual Download Page 9

Page: 9 / 100

I. Specifications

A. Electrical and Refrigerant Data

Design Pressure (PSIG) Refrigerant

Model

AC Supply Voltage

Amperes

R-404A

RH1-SSB(-HD)(-CF)

115/60/1

7.0

450

200

12.2 oz.

RH2-SSB(-HD)

115/60/1

10.0

450

200

18.2 oz.

RH3-SSB(-HD)(-FG)(-HG)

115/60/1

13.0

450

200

23.2 oz.

RH1-SSB-GD

115/60/1

10.7

450

200

16.1 oz.

RH2-SSB-GD

115/60/1

11.8

400

200

21.5 oz.

RH3-SSB-GD

115/60/1

15.5

450

250

31.4 oz.

FH1-SSB(-HD)

115/60/1

11.0

450

250

15.2 oz.

FH2-SSB(-HD)

115/60/1

15.5

450

250

20.1 oz.

FH2-SSB-HDCU

115/60/1

15.5

450

250

20.1 oz.

PTR1SSB-xxxx / PTR1SSB01-10

115/60/1

12.0

450

250

15.5 oz.

PTR2SSB-FSFS(-HSHS)

115/60/1

12.0

450

250

21.5 oz.

PTR2SSB-FGFG(-HGHG)

115/60/1

12.8

450

250

17.3 oz.

RIR1-SSB

115/60/1

7.0

450

200

12.2 oz.

RIR2-SSB

115/60/1

11.0

450

200

18.2 oz.

RIR2-SSB51-02

115/60/1

11.0

450

200

18.2 oz.

RTR1-SSB

115/60/1

7.0

450

200

12.2 oz.

Design Pressure (PSIG)

Refrigerant

Model

Supply

Voltage Amperes

Refrigerator

Freezer

R-404A

R-134a

Ref.

Freezer

Ref.

RFH1-SSB-HD

115/60/1

16.0

450

250

450

250

9.5 oz.

12.0 oz.

RFH1-SSB(-HS)(-HSE) 115/60/1

9.5

240

120

450

250

12.1 oz.

9.1 oz.

RFH2-SSB(-HD)

115/60/1

16.6

450

200

450

250

12.2 oz.

15.2 oz.

RFH3-SSB(-HD)

115/60/1

450

200

450

250

18.2 oz.

15.2 oz.

See the nameplate for electrical and refrigeration specifications. The nameplate is located
on the right side wall of the cabinet interior.

Note: We reserve the right to make changes in specifications and design without prior

notice.

Summary of Contents for FH1-SSB(-HD)





































































































Search results

Summary of Contents for FH1-SSB(-HD)

Reviews:

Hoshizaki FH1-SSB(-HD), Service Manual, Page: 9 / 100

Search results

Summary of Contents for FH1-SSB(-HD)

Reviews: