Hoshizaki FH1-SSB(-HD) Service Manual Download Page 19

Page: 19 / 100

3c) Cool Down Achieved: RFH1-SSB-HD Freezer

LED 5 (CPH and DrH (auxiliary code Q-5 and later)) is on. LED 3 (EvapFM on)
is off:

CB monitors cooling of the cabinet via CTh. CTh cools to 3

F (1.7

C) below

setpoint. EvapFM continues. Comp and ConFM de-energize. CPH and DrH (auxiliary
code Q-5 and later) energize.

4a) Cool Down Restart: Freezer (auxiliary code P-5 and earlier)

LEDs 4 (Comp) and 5 (ConFM) are on. LED 3 (EvapFM on) is off:

CTh warms

to 3

F (1.7

C) above setpoint. 2.5-minute Comp off delay timer terminates. Comp,

ConFM, and EvapFM energize.

4b) Cool Down Restart: Freezer (auxiliary code P-6 and later)

LEDs 4 (Comp) and 5 (ConFM) are on. LED 3 (EvapFM on) is off:

CTh warms

to 3

F (1.7

C) above setpoint. 2.5-minute Comp off delay timer terminates. EvapFM

continues. Comp and ConFM energize.

4c) Cool Down Restart: RFH1-SSB-HD Freezer

LEDs 4 (Comp and ConFM) and 5 (CPH and DrH (auxiliary code Q-5 and later))
are on. LED 3 (EvapFM on) is off:

CTh warms to 3

F (1.7

C) above setpoint.

2.5-minute Comp off delay timer terminates. EvapFM, CPH, and DrH (auxiliary code
Q-5 and later) continue. Comp and ConFM energize.

4d) Cool Down Restart: RFH1-SSB(-HS)(-HSE) Freezer

LEDs 4 (Comp and ConFM) and 5 (DrH, PH, and MH) are on. LED 3 (EvapFM on)
is off:

CTh warms to 3

F (1.7

C) above setpoint. 2.5-minute Comp delay timer

terminates. Comp, ConFM, EvapFM, DrH, PH and MH energize.

5a) Defrost: Freezer (auxiliary code P-5 and earlier) and RFH1-SSB(-HS)(-HSE) Freezer

(1) Time-Initiated Defrost or Manual-Initiated Defrost

a1)

Freezer (auxiliary code P-5 and earlier)–LEDs 1 (DH) and 3 (EvapFM

off) are on:

DT terminates or manual defrost initiated. 20-minute minimum

defrost timer starts. 1-hour maximum defrost timer starts. DH energizes.

"dEF" displayed on DB.

If energized, Comp, ConFM, and EvapFM de-energize.

a2)

RFH1-SSB(-HS)(-HSE) Freezer–LEDs 1 (DH) and 3 (EvapFM off) are on:

DT terminates or manual defrost initiated. 20-minute minimum defrost timer
starts. 1-hour maximum defrost timer starts. DH energizes.

"dEF" displayed on

DB. If energized, Comp, ConFM, and EvapFM de-energize. DrH, PH, and MH
de-energize.

The time-initiated defrost is factory set to 6 times per day (every 4 hours. For

further details, see "II.E.1.b) Defrost Frequency." Before changing this setting,

contact Hoshizaki Technical Support at 1-800-233-1940 for recommendations.

Summary of Contents for FH1-SSB(-HD)





































































































Search results

Summary of Contents for FH1-SSB(-HD)

Reviews:

Related manuals for FH1-SSB(-HD)

Brands by name

Popular brands

Hoshizaki FH1-SSB(-HD), Service Manual

Search results

Summary of Contents for FH1-SSB(-HD)

Reviews:

Related manuals for FH1-SSB(-HD)

Brands by name

Popular brands