Honeywell XK516D1 Maintenance Manual Download

Page: 284 / 300

Honeywell

COMPONENT MAINTENANCE MANUAL

PART NUMBER 964-0452

I.B.1516A Page 701

Oct 25/02

23-12-01

ASSEMBLY (INCLUDING STORAGE)

1. General

Observe all labels that were attached to electrical leads, assemblies, subassemblies, and parts
during disassembly and repair.

Assembly materials are listed in Fig. 701. Fits, clearances, and dimensions are given in the

FITS

AND CLEARANCES

section. Special tools are listed in the

SPECIAL TOOLS, FIXTURES, AND

EQUIPMENT

section.

NOTE: Equivalent substitutes may be used for all assembly materials.

Assembly Materials

Figure 701

CAUTION: ELECTROSTATIC DISCHARGE SENSITIVE (ESDS) DEVICES ARE SUBJECT TO DAM-

AGE BY EXCESSIVE LEVELS OF VOLTAGE. REFER TO DOD-HDBK-263 FOR PROPER
HANDLING PROCEDURES.

2. Transceiver Assembly (Ref. IPL Fig. 1)

A. Housing

(1) Install troughing (57) into chassis, and secure with screws (58).

(2) Install guides (53) on front wall (48); secure with screws (56), posts (55), and screws (54).

(3) Install hooks (50) on front wall (48), and secure with screws (51) and washers (52).

(4) Position front wall (48) in chassis, and secure with screws (49).

(5) Install label (58A) on chassis only if replacement is required.

B. Motherboard, A6

(1) Install Motherboard, A6 (28) and foil (27) into chassis,, and secure with screws (29).

(2) Connect cable, W1, connectors, X330 and X210, on mating connectors on Motherboard.

C. EMC Filter, A7

(1) Install EMC Filter, A7 (22) in chassis.

(2) Connect flexprint cables, W74 and W76, in their mating connectors, X74 and X76, on the

EMC Filter module.

(3) Install cable, W3 (21) connector, X72, on EMC Filter module.

(4) Install rear panel (30) on rear of chassis,, and secure with screws (11, 23, and 31).

ITEM

MANUFACTURER AND SPECIFICATION

USE

1. Adhesive

Loctite 222, manufactured by Loctite Corp. (V05972),
705 N Mountain Rd., Newington, CT 02021-2513.

Retain screws.

2. Lacing cord

No. 4, Type I, Finish B per MIL-T-43455.

Wire bundle ties.

3. Sealant

P/S 890, Class B, manufactured by PRC-DeSoto
International, Inc. (V92108), PO Box 1800, Glendale,
CA 91209-1800 per MIL-S-8802, Type II, Class B.

Sealing connecors
and insulators.

Summary of Contents for XK516D1













































































































































































































































































































Search results

Summary of Contents for XK516D1

Reviews:

Related manuals for XK516D1

Brands by name

Popular brands

Honeywell XK516D1, Maintenance Manual

Search results

Summary of Contents for XK516D1

Reviews:

Related manuals for XK516D1

Brands by name

Popular brands