Honeywell XK516D1 Maintenance Manual Download

Page: 96 / 300

Honeywell

COMPONENT MAINTENANCE MANUAL

PART NUMBER 964-0452

I.B.1516A Page 102

Oct 25/02

23-12-01

(3) Install the GSE Setup software diskette, Part No. 998-2403-50X, into drive A of the PC

(if A is not the current drive, substitute the proper drive).

(4) From the Program Manager, select

File, Run

(5) In the command line, type:

a:setup

. Click

. The GSE Setup Software is loaded into

the PC. When complete (the DOS prompt returns), remove the diskette from the drive.

B. ATP Software Installation

Use this procedure to install a new release of the ATP software.

(1) Launch MS-Windows by typing

win

at the DOS prompt.

(2) Install the ATP Setup diskette, Part No. 998-2402-50X, into drive A.

(3) From the Program Manager select

File, Run

(4) In the command line, type:

a:setup

. Click

(5) When prompted to enter the ATEasy directory, if ATEasy is already entered select

If not, enter ATEASY as the root directory, then select

. The test software is loaded

into the proper directories, and a separate program group of 2 icons appears in the HFDR
folder. These icons are labelled HFDR ATP and Coupler ATP.

(6) Remove diskette from drive.

C. CFDS Software Installation

Use this procedure to install a new release of the CFDS software.

(1) Launch MS-Windows by typing

win

at the DOS prompt.

(2) Install the CFDS Setup diskette, Part No. 998-2885-50X, into drive A.

(3) From the Program Manager, select

File, Run

(4) In the command line, type:

a:setup

. Click

(5) When prompted to enter the ATEasy directory, if ATEasy is already entered, select

If not, enter ATEASY as the root directory, then select

. The test software is loaded

into the proper directories, and a new group of 4 icons appears in the HFDR folder. These
icons are labelled XCVR, ADP, CPLR, and CFDS.

(6) Remove diskette from drive.

6. HF Transceiver Test Setup

A. Verify that the test equipment is set up as shown in the Test Setup of Fig. 101.

B. If an FK516 (or FK517) Coupler and Coupler Bench Tray/Dummy Antenna are available, con-

nect the output of the RF Power Meter to the FK516 (or FK517) Coupler, using the appropri-
ate Coupler Interface Cable.

C. If no Antenna Coupler is available for the test setup, install a jumper between KEY INTER-

LOCK (MP-5H) and 28V (BP-11) on the HFDR Breakout Panel, and connect the 50-ohm load
to the RF Power Meter as shown in Fig. 101.

NOTE: A printer is optional. The ATP will execute whether or not a printer is present, but to

record the ATP test results, a printer is recommended. The test results may be trans-
ferred to another PC that can read and print text files.

Summary of Contents for XK516D1













































































































































































































































































































Search results

Summary of Contents for XK516D1

Reviews:

Related manuals for XK516D1

Brands by name

Popular brands

Honeywell XK516D1, Maintenance Manual

Search results

Summary of Contents for XK516D1

Reviews:

Related manuals for XK516D1

Brands by name

Popular brands