Honeywell Voyager 1400g Series User Manual Download Page 5

Page: 5 / 216

Honeywell Scanning & Mobility Product
Environmental Information

Refer to www.honeywellaidc.com/environmental for the RoHS / REACH /
WEEE information.

Australia/NZ

C-Tick Statement

Conforms to AS/NZS 3548 EMC requirement

Russia

Gost-R certificate

South Korea

The product meets Korean agency approval for Class B equipment:

이 기기는 가정용 (B 급 ) 전자파적합기기로서 주로 가정에서 사용
하는 것을 목적으로 하며 ,

모든 지역에서 사용할 수 있습니다 .

Taiwan

If the following label is attached to your product, the product meets Taiwan
agency approval:

BSMI Standard: CNS13438, CNS14336-1

依據標準

: CNS13438, CNS14336-1

International

LED Safety Statement

The LED has been tested and classified as “EXEMPT RISK GROUP” to the
standard: IEC 62471:2006.

CB Scheme

Certified to CB Scheme IEC 60950-1, Second Edition.

Summary of Contents for Voyager 1400g Series

























































































































































































































Search results

Summary of Contents for Voyager 1400g Series

Reviews:

Honeywell Voyager 1400g Series, User Manual, Page: 5 / 216

Search results

Summary of Contents for Voyager 1400g Series

Reviews: