manualshive.com logo in svg

Honeywell Voyager 1400g Series, User Manual, Page: 48 / 216

Share
Download
Honeywell Voyager 1400g Series User Manual Download Page 48

2 - 24

the scanner waits for ACK/NAK again.  Turn on the ACK/NAK protocol by 
scanning the 

ACK/NAK On

 bar code below.  To turn off the protocol, scan 

ACK/NAK Off

.  

Default = ACK/NAK Off

.

Scanner to Bioptic Communication

The following settings are used to set up communication between Honeywell 
scanners and bioptic scanners.  

Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout 

must be set to 3000 in order to communicate with a bioptic scanner.  See 

RS232 Baud Rate

 on page 2-20, and 

RS232 Timeout

on page 2-23 for 

further information.

Scanner-Bioptic Packet Mode

Packet Mode On

 must be scanned to set the scanner’s format so it is com-

patible with a bioptic scanner.  

Default = Packet Mode Off.

ACK/NAK On

 * ACK/NAK Off

* Packet Mode Off 

Packet Mode On 

Summary of Contents for Voyager 1400g Series

























































































































































































































Reviews:

No comments