manualshive.com logo in svg

Honeywell Voyager 1400g Series, User Manual, Page: 18 / 216

Share
Download
Honeywell Voyager 1400g Series User Manual Download Page 18

1 - 2

2.

The scanner beeps.  

3.

Verify the scanner operation by scanning a bar code from the 

Sample 

Symbols

 in the back of this manual.

The unit defaults to a USB PC Keyboard.  Refer to 

page 2-4

 for other USB 

terminal settings.

For additional USB programming and technical information, refer to “USB 
Application Note,” available at 

www.honeywellaidc.com.

Connecting with Keyboard Wedge

A scanner can be connected between the keyboard and PC as a “keyboard 
wedge,” where the scanner provides data output that is similar to keyboard 
entries.  The following is an example of a keyboard wedge connection:

1.

Turn off power and disconnect the keyboard cable from the back of the 
terminal/computer.

2.

Connect the appropriate interface cable to the device and to the 
terminal/computer.

Summary of Contents for Voyager 1400g Series

























































































































































































































Reviews:

No comments