manualshive.com logo in svg

Honeywell AlarmNet 7810iR, Installation And Setup Gude, Page: 61 / 64

Share
Download
Honeywell AlarmNet 7810iR Installation And Setup Gude Download Page 61

Section 7: Diagnostics and Troubleshooting 

7-9 

 
 

Action Screen 

Display 

3.  Press the center of the square. 

The Touch 

Screen Calibration

 screen displays 

Next 

press the center of the box in lower right 
corner. 

 

 

4.  Press the center of the square. 

The Touch 

Screen Calibration

 screen displays 

Next 

press the center of the box in lower left 
corner.

 

 

5.  Press the center of the square. 

The Touch 

Screen Calibration

 screen displays Touch 

target to verify calibration. 

 

6.  Press the center of the square. If touch 
screen calibration was successful, you are 
returned automatically to the 
"Diagnostics/Tests" screen.  

If touch screen calibration was not successful, 

Calibration Unsuccessful 

is displayed 

momentarily. You are then returned 
automatically to the first 

Touch Screen 

Calibration

 screen. 

NOTE: You will progress through the 

Touch 

Screen Calibration

 screens regardless of 

where you touch. To successfully calibrate the 
touch screen, you must press the center of the 
box on each screen. 

 

 

Summary of Contents for AlarmNet 7810iR

































































Reviews:

No comments