manualshive.com logo in svg

Honeywell AlarmNet 7810iR, Installation And Setup Gude, Page: 59 / 64

Share
Download
Honeywell AlarmNet 7810iR Installation And Setup Gude Download Page 59

Section 7: Diagnostics and Troubleshooting 

7-7 

LED Test 

Perform the LED Test as follows: 

Action Screen 

Display 

1. Press the 

Test 

button associated with the 

LED Test. "Testing.." is displayed (yellow) in 
the test status column on the 
"Diagnostics/Tests" screen while the 4 LEDs 
light sequentially, left to right (amber, red, 
green, green), 5 times.  At the conclusion of 
the test, a pop-up "Confirmation Window" is 
displayed in the center of the 
"Diagnostics/Tests" screen. 

 

 

2.  Within the Confirmation Window the 
question "Did you see chasing LED pattern?" 
is displayed. 

If you press the 

Yes

 button, a green "Passed." 

indication is displayed in the test status 
column on the "Diagnostics/Tests" screen. 

If you press the 

No

 button, a red "Failed." 

indication is displayed in the test status 
column on the "Diagnostics/Tests" screen. 

 

 

Summary of Contents for AlarmNet 7810iR

































































Reviews:

No comments