manualshive.com logo in svg

Honeywell AlarmNet 7810iR, Installation And Setup Gude, Page: 60 / 64

Share
Download
Honeywell AlarmNet 7810iR Installation And Setup Gude Download Page 60

7810iR Internet Communication Module Installation and Setup Guide 

7-8 

 

Keypad Test 

The Keypad Test is not applicable for 7810iR. 

Touch Screen Calibration 

Calibrate the touch screen as follows:  

Action Screen 

Display 

1.  Press the 

Diagnostics

 button on the 

"Advanced Setup" menu screen.  The 
"Diagnostics/Test" screen is displayed. 

 

2. Begin the Touch Screen calibration from the 
"Diagnostics/Tests" screen by pressing the 

Calibrate

 button. When the 

Calibrate

 button is 

pressed, the 

Touch Screen Calibration

 

screen is displayed. 

Within the 

Touch Screen Calibration

 screen 

you are asked to 

Press the center of the box 

in upper left corner.

 Press the center of the 

square. 

When this square is touched, the 

Touch 

Screen Calibration

 screen displays 

Next 

press the center of the box in the upper 
right corner.

 

 

 

 

 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for AlarmNet 7810iR

































































Reviews:

No comments