manualshive.com logo in svg

Honeywell AlarmNet 7810iR, Installation And Setup Gude, Page: 28 / 64

Share
Download
Honeywell AlarmNet 7810iR Installation And Setup Gude Download Page 28

7810iR Internet Communication Module Installation and Setup Guide 

5-4 

 
 

Action Screen 

Display 

3.  Alarm message sent to LRR Line Card, 
local message pushed into History Window. 

 

 

 

 

 

Fail to Manual 

 

UL

 

 

Fail to Manual Mode cannot be used with UL installations. 

 

 

If Fail to Manual is selected and there is a loss of communication between the 7810iR and 
the LRR Line Card, an incoming message will be reported as undeliverable to AlarmNet 
after approximately 30 seconds.  AlarmNet will then route all messages to the secondary CS. 

Action Screen 

Display 

1.  Loss of  Line Card communication with 
Fail to Manual feature selected.  Operator 
must manually respond to incoming alarms. 

 

2.  Loss of Line Card communication with 
Fail to Manual feature NOT selected. All 
messages from AlarmNet will be bounced.  
AlarmNet will route all message traffic for this 
CS to the Backup Account CS. 

 

 

Summary of Contents for AlarmNet 7810iR

































































Reviews:

No comments