manualshive.com logo in svg

Honeywell AlarmNet 7810iR, Installation And Setup Gude, Page: 31 / 64

Share
Download
Honeywell AlarmNet 7810iR Installation And Setup Gude Download Page 31

Section 5: Operation 

5-7 

 
 

Action Screen 

Display 

3.  Alarm message sent to Automation 
Equipment, local message pushed into 
History Window. 

 

Fail to Manual 

 

UL

 

 

Fail to Manual Mode cannot be used with UL installations. 

 

 

If Fail to Manual is selected and there is a loss of communication between the 7810iR and 
the Automation system, an incoming message will be reported as undeliverable to AlarmNet 
after approximately 30 seconds.  AlarmNet will then route all messages to the secondary CS. 

Action Screen 

Display 

1.  Loss of Automation Equipment 
communication with Fail to Manual feature 
selected.  Operator must manually respond 
to incoming alarms. 

 

2.  Loss of Automation Equipment 
communication with Fail to Manual feature 

NOT

 selected. All messages from AlarmNet 

will be bounced.  AlarmNet will route all 
message traffic for this CS to the Backup 
Account CS. 

 

 

Summary of Contents for AlarmNet 7810iR

































































Reviews:

No comments