manualshive.com logo in svg

Honda in-VEHICLE ENTERTAINMENT SYSTEM 08A60-S0X-100, Installation Instructions Manual

Share
Download
Honda in-VEHICLE ENTERTAINMENT SYSTEM 08A60-S0X-100 Installation Instructions Manual Download Page 9

© 2001 American Honda Motor Co., Inc - All Rights Reserved.

AII 22054 (0104)

9 of 14

31. Wrap a piece of wire around the 16-pin

connector. Using electrical tape, secure the wire
to the connector so that the end of the wire will
not get caught. Pull the 16-pin connector behind
the headliner and out of the small cutout until the
harness clip comes through the cutout. Remove
the tape and the wire.

i-VES

HARNESS

PIECE OF
WIRE

 

i-VES

 HARNESS

16-PIN CONNECTOR
(BLACK)

ELECTRICAL
TAPE

32. Get the butterfly bracket. Insert the butterfly

bracket into the elongated hole in the roof panel,
then turn it clockwise to lock it into position.

33. Position the monitor bracket on the roof panel,

install a lock nut onto the butterfly bracket, and
install the two 5 x 14 mm washer-screws.
Tighten the locknut and the washer-screws
securely.

ELONGATED HOLE

BUTTERFLY
BRACKET

 Turn the bracket clockwise
 to lock it into position.

MONITOR
BRACKET

LOCK NUT

5 x 14 mm
WASHER-SCREWS

34. Connect the 16-pin (black) 

i-VES

 harness

connector to the monitor console, then secure
the monitor console to the monitor bracket with
the four 4 x 19 mm self-tapping screws. Secure
the harness clip of the 

i-VES

 harness to the rib

of the monitor console as shown.

MONITOR
BRACKET

MONITOR
CONSOLE

i-VES

 HARNESS

HARNESS
CLIP

Secure the harness
clip to the rib of the
monitor console.

4 x 19 mm
SELF-TAPPING SCREWS

Summary of Contents for in-VEHICLE ENTERTAINMENT SYSTEM 08A60-S0X-100















Reviews:

No comments

Brands by name

Popular brands

Load more brands