manualshive.com logo in svg

Honda in-VEHICLE ENTERTAINMENT SYSTEM 08A60-S0X-100, Installation Instructions Manual

Share
Download
Honda in-VEHICLE ENTERTAINMENT SYSTEM 08A60-S0X-100 Installation Instructions Manual Download Page 12

12 of 14

AII 22054 (0104)

© 2001 American Honda Motor Co., Inc - All Rights Reserved.

47. Plug the 4-pin black connector of the 

i-VES

harness into the FM modulator.

4-PIN BLACK CONNECTOR
of 

i-VES

 HARNESS

FM
MODULATOR

FREQUENCY
ADJUSTMENT
SWITCH

i-VES

 HARNESS

RED JACK

i-VES

 HARNESS

WHITE JACK

FM modulator frequency switch setting:
Adjust only switches 3, 4, and 5.

88.1MHz 88.3MHz 88.5MHz 88.7MHz

88.9MHz 89.1MHz 89.3MHz 89.5MHz

Factory
Default

1

2

3

4

5

1

2

3

4

5

1

2

3

4

5

1

2

3

4

5

1

2

3

4

5

1

2

3

4

5

1

2

3

4

5

1

2

3

4

5

48. Plug the red and white jacks of the 

i-VES

harness into the FM modulator.

49. The factory frequency setting for the FM

modulator is set at 88.3MHz.

NOTE: If the factory frequency setting is used by
a local radio station, pick an unused radio
frequency. Use the chart below to select a
frequency that is not used. Write down the new
frequency setting in the owner's manual supplied
with the 

i-VES, 

and notify the customer of the

change.

50. Route the two leads of the FM modulator to the

console opening.

VEHICLE ANTENNA
LEAD

FM MODULATOR

FM MODULATOR
MALE ANTENNA
LEAD

80 mm

Loop the antenna leads, and
secure them with one wire tie.

FM MODULATOR

WIRE TIE

51. Connect the female antenna lead of the FM

modulator to the vehicle antenna lead.

52. Pull the male antenna lead from the FM

modulator out 80 mm through the radio opening.

53. Loop the excess FM modulator antenna cable,

and secure it with one wire tie.

FM MODULATOR
FEMALE ANTENNA
LEAD

Summary of Contents for in-VEHICLE ENTERTAINMENT SYSTEM 08A60-S0X-100















Reviews:

No comments

Brands by name

Popular brands

Load more brands