manualshive.com logo in svg

Honda in-VEHICLE ENTERTAINMENT SYSTEM 08A60-S0X-100, Installation Instructions Manual

Share
Download
Honda in-VEHICLE ENTERTAINMENT SYSTEM 08A60-S0X-100 Installation Instructions Manual Download Page 7

© 2001 American Honda Motor Co., Inc - All Rights Reserved.

AII 22054 (0104)

7 of 14

22. On the passenger's side of the vehicle, remove

the front door opening trim around the front pillar
trim. Remove the front pillar trim (four clips).

24. On the passenger's side of the vehicle, remove

the grab handle (two caps, two Torx bolts, and
two washers).

FRONT PILLAR
TRIM

FRONT DOOR
OPENING TRIM

CLIP (4)

Unplug the
vehicle connectors.

TORX
BOLTS

SUNVISOR

23. Remove the sunvisor on the passenger's side

(two Torx bolts, and unplug the connectors).

GRAB
HANDLE

COVER

TORX
BOLTS

ROOF CEILING VENT

RETAINING
TAB

LENS

25. On the passenger's side of the vehicle, remove

the lens from the roof ceiling vent at the second
row by releasing the four retaining tabs. Take
care not to damage the retaining tabs.

Summary of Contents for in-VEHICLE ENTERTAINMENT SYSTEM 08A60-S0X-100















Reviews:

No comments

Brands by name

Popular brands

Load more brands