manualshive.com logo in svg

Honda in-VEHICLE ENTERTAINMENT SYSTEM 08A60-S0X-100, Installation Instructions Manual

Share
Download
Honda in-VEHICLE ENTERTAINMENT SYSTEM 08A60-S0X-100 Installation Instructions Manual Download Page 11

© 2001 American Honda Motor Co., Inc - All Rights Reserved.

AII 22054 (0104)

11 of 14

41. Wrap electrical tape around the accessory

socket harness connector disconnected in step
11; it will not be reused. Secure the accessory
socket harness to the 

i-

VES harness with one

wire tie in the area shown.

43. Reinstall the center lower console with the four

screws removed in step 12. Do not reinstall the
two bolts; they are not reused.

ELECTRICAL TAPE

ACCESSORY
SOCKET HARNESS

WIRE
TIE

i-VES

HARNESS

NAVAGATION UNIT
HARNESS

ACCESSORY
SOCKET
HARNESS

WIRE
TIE

If the vehicle you are working on is equipped with
a navigation unit, continue with step 42;
otherwise, go to step 44.

42. Secure the navagation unit harness freed from

the body frame in step 13 to the 

i-VES

 harness

with one wire tie.

SCREW

CENTER LOWER
CONSOLE

SCREWS

SCREW

SELF-TAPPING SCREWS

VEHICLE BOLT
(Discard.)

8 x 25 mm
BOLT

8 mm PLAIN
WASHERS

8 mm
FLANGE NUT

RIGHT
VCP
BRACKET

LOWER
BRACKET

44. At the rear of the center lower console, remove

and discard the vehicle bolt, and install the
8 x 25 mm bolt from the kit. Repeat on the other
side of the center console.

45. Reinstall the center lower trim removed in

step 9.

46. Install the right VCP bracket using two of the

self-tapping screws removed in step 10; then
secure the lower bracket with two plain washers,
and one 8 mm flange nut.

i-VES

HARNESS

Summary of Contents for in-VEHICLE ENTERTAINMENT SYSTEM 08A60-S0X-100















Reviews:

No comments

Brands by name

Popular brands

Load more brands