manualshive.com logo in svg

Honda in-VEHICLE ENTERTAINMENT SYSTEM 08A60-S0X-100, Installation Instructions Manual

Share
Download
Honda in-VEHICLE ENTERTAINMENT SYSTEM 08A60-S0X-100 Installation Instructions Manual Download Page 13

© 2001 American Honda Motor Co., Inc - All Rights Reserved.

AII 22054 (0104)

13 of 14

LEFT VCP BRACKET

SELF-TAPPING
SCREWS
(Reused; do not

tighten yet.)

8 mm
PLAIN-WASHERS

8 mm
FLANGE NUT

LOWER
BRACKET

i-VES

 HARNESS

6-PIN WHITE CONNECTOR

LEFT VCP
BRACKET

POWER
FILTER

i-VES 

HARNESS

26-PIN CONNECTOR

VCP

4 x 10 mm
SCREWS

i-VES 

HARNESS

16-PIN CONNECTOR

ACCESSORY
SOCKET

VCP
CONSOLE

SOCKET
HOLDER

54. Install the left VCP bracket using two of the self-

tapping screws removed in step 10, and secure
the lower bracket with two 8 mm plain-washers
and one 8 mm flange nut.

56. Position the VCP on the right and left VCP

brackets, and install the four 4 x 10 mm screws.

55. Plug the 6-pin white connector of the 

i-VES

harness into the power filter on the left VCP
bracket.

57. Plug the 16-pin and 26-pin connectors of the

i-VES

 harness into the VCP.

Installing the VCP Console

58. Install the accessory socket and socket holder

removed in step 11 onto the VCP console.

4 x 10 mm
SCREWS

Summary of Contents for in-VEHICLE ENTERTAINMENT SYSTEM 08A60-S0X-100















Reviews:

No comments

Brands by name

Popular brands

Load more brands