manualshive.com logo in svg

Honda in-VEHICLE ENTERTAINMENT SYSTEM 08A60-S0X-100, Installation Instructions Manual

Share
Download
Honda in-VEHICLE ENTERTAINMENT SYSTEM 08A60-S0X-100 Installation Instructions Manual Download Page 8

8 of 14

AII 22054 (0104)

© 2001 American Honda Motor Co., Inc - All Rights Reserved.

26. Move the vent knob to the CLOSE position, then

remove the two screws that fasten the roof
ceiling vent. Unplug the vehicle connector, and
remove the roof ceiling vent.

Routing the 

i-VES

 Harness

28. Route the two 20-pin connectors from the 

i-VES

harness up and out of the radio opening.

VEHICLE
CONNECTOR

ROOF
CEILING
VENT

SCREW
(Black )

SCREW

SCREW
(Gold)

27. Remove the center table arm cover (four clips).

Remove the center table (three nuts).

NUTS

CENTER
TABLE

i-VES

 HARNESS

(BLACK 16-PIN

CONNECTOR SIDE)

i-VES

 HARNESS

20-PIN
CONNECTORS

29. Route the 16-pin (black) connector end of the

 

i-VES

 harness through the center lower console,

behind the dash, and along the passenger's door
toward the center pillar.

30. Continue routing the 16-pin connector of the

i-VES

 harness up the center pillar.

CENTER
PILLAR

16-PIN
CONNECTOR
(BLACK)

i-VES

HARNESS

Route inside the
floor panel.

FLOOR
CARPET

Summary of Contents for in-VEHICLE ENTERTAINMENT SYSTEM 08A60-S0X-100















Reviews:

No comments

Brands by name

Popular brands

Load more brands