HNP Mikrosysteme mzr-7240 Operating Manual Download Page 41

Page: 41 / 89

6 Optional motor versions

Operating manual mzr-7240

Last update: March 2019

Technical data subject to change without prior notice!

The micro annular gear pump may now be put into operation by increasing

the external voltage signal. A voltage signal of 0 V corresponds to 0 rpm

and 10 V to the maximal programmed.

Remarks

−

You may adjust speed of the micro annular gear pump without the need to

connect it to the serial interface.

−

In case error occurs for example due to the motor overload - the green status

LED on the terminal Box S-G05 will turn red.

6.5.2.5

Startup with the RS-232 interface

Connect the drive with the eight colored wires to the S-G05. The colors of

the corresponding wire connections are in table 24.

In order to prevent uncontrolled startup of the pump, bring the

potentiometer knob to the null position by turning it clockwise to the limit

stop.

Put the DIP-switch to »Poti« position.

Connect the RS-232 interface of the Terminal Box S-G05 with a free serial

interface of a PC. Use for that the delivered 9-pole null-modem cable.

Now install the delivered software as described in the chapter 9 or

Chapter 10.

Connect the 24 VDC voltage supply to the terminal or to the DIN

connector.

Provide for a steady liquid supply to the pump in order to avoid dry

operation of the device.

The micro annular gear pump may now be put into operation with the

available software (operating mode RS-232 see chapter 10).

Remarks

−

In case error occurs for example due to the motor overload - the green error

status LED on the Terminal Box S-G05 will turn red.

Summary of Contents for mzr-7240


























































































Search results

Summary of Contents for mzr-7240

Reviews:

Related manuals for mzr-7240

Brands by name

Popular brands

HNP Mikrosysteme mzr-7240, Operating Manual

Search results

Summary of Contents for mzr-7240

Reviews:

Related manuals for mzr-7240

Brands by name

Popular brands