HNP Mikrosysteme mzr-7240 Operating Manual Download Page 67

Page: 67 / 89

13 EU Directive

Operating manual mzr-7240

Last update: March 2019

Technical data subject to change without prior notice!

13.1.2

Information on use as intended

For micro annular gear pumps, note the following:

Requirement for the intended operation is the operation according to the

technical data and the manual.

Restrictions

If the micro annular gear pumps are used at home, in business or in commerce

or in small businesses, appropriate measures must be taken to ensure that

emitted interferences are below the permitted limit a values!

Installation instructions:

The power supply and motor supply cable must be connected directly to the

terminal box S-G05.

During the operation of micro annular gear pumps with a multiplexer board the

connection of the terminal box S-G05 is not possible.

For the control unit S-KG no further conditions must be fulfilled in order to

comply with the EMC-protection requirements.

Summary of Contents for mzr-7240


























































































Search results

Summary of Contents for mzr-7240

Reviews:

Related manuals for mzr-7240

Brands by name

Popular brands

HNP Mikrosysteme mzr-7240, Operating Manual

Search results

Summary of Contents for mzr-7240

Reviews:

Related manuals for mzr-7240

Brands by name

Popular brands