HNP Mikrosysteme mzr-7240 Operating Manual Download Page 30

Page: 30 / 89

6 Optional motor versions

Operating manual mzr-7240

Technical data subject to change without prior notice!

Last update: March 2019

6.3

Stepper motor without encoder as mzr-7243

The micro annular gear pump mzr-7240 may alternatively be a stepper motor

drives. This has next to the smaller size for a limited speed range.

Stepper motor

Motor type

M-1715-1,5S

Speed range

1 – 500 rpm

Phase resistance (at 20°C)

2,1

Ω

(± 10%)

Inductance per phase (1 kHz)

5 mH (± 20%)

Nominal current per phase (2 current phases) 1,5 A
Holding torque (2 current phases)

420 mNm

Length cable

300 mm

Ambient temperature [°C]

-10 … + 50°C

Weight

230 g

table 13

Technical data for the stepper motor

Function Motor cable

Cable

Colour

Phase

black

Phase

green

Phase

red

Phase

blue

table 14

Wiring of the motor cable (alternative colour possible)

Summary of Contents for mzr-7240


























































































Search results

Summary of Contents for mzr-7240

Reviews:

Related manuals for mzr-7240

Brands by name

Popular brands

HNP Mikrosysteme mzr-7240, Operating Manual

Search results

Summary of Contents for mzr-7240

Reviews:

Related manuals for mzr-7240

Brands by name

Popular brands