HNP Mikrosysteme mzr-7240 Operating Manual Download Page 48

Page: 48 / 89

7 System integration

Operating manual mzr-7240

Technical data subject to change without prior notice!

Last update: March 2019

Warning

Please check that all wetted parts of the fluidic system are clean. Clean these

parts in case before mounting the pump.

Please check whether there are swarfs in the screw connections, pollution

remaining in reservoirs or soiling in valves, pipe work or filters.

The micro annular gear pump mzr-7240 is available in two versions. The liquid

supply openings may be lateral or front with a 1/8" NPT thread screw. Pump

heads equipped with the heating module are available with front liquid ports

only.

Lateral screw connection 1/8" NPT

figure 26

Fluid connection fitting 1/8" NPT, stainless steel

The thread of the fitting should be wrapped with 2-3 layers of PTFE tape

and screwed in the NPT thread (see table 27). First manually, then

tightened with ½ to ¾ wrench turns.

Summary of Contents for mzr-7240


























































































Search results

Summary of Contents for mzr-7240

Reviews:

Related manuals for mzr-7240

Brands by name

Popular brands

HNP Mikrosysteme mzr-7240, Operating Manual

Search results

Summary of Contents for mzr-7240

Reviews:

Related manuals for mzr-7240

Brands by name

Popular brands