HNP Mikrosysteme mzr-4622 Operating Manual Download

Page: 72 / 92

12 Problems and their removal

Operation manual mzr-4622

Technical data subject to change without prior notice!

Last update: March 2019

Disturbance

Cause

Solution

lower level as the pump.

17 Excess temperature

The surface of the pump is hot.

Clean the surface of the pump, rinse the
pump.

The pump operates with difficulty.

The pump should be flushed.

Particles in the delivered liquid or deposits
in the pump

The operation of the pump should
immediately be stopped! Return the pump to
the manufacturer for cleansing.

Noise of beveling

The operation of the pump should
immediately be stopped! Return the pump to
the manufacturer for cleansing and repair.

The motor surface or the motor interior are
too hot.

High temperature indicator in the drive is on.
The motor has been shut down by the
thermistor. Return the pump to the
manufacturer.

18 The pump is noisy.

Wear out of the pump or defective
components.

Do not continue to operate the pump, return
it to the manufacturer for maintenance.

19 Overcurrent

Particles in the delivered liquid

Rinse the pump.

The pump operates with difficulty.

Dosing needle is damaged. Needle should be
cleansed, flushed or exchanged.

Tubing on the delivery side, dosing needle or
the non-return valve are blocked. Cleanse,
flush or exchange the components.

Deposits inside the pump.

Flush the pump. If necessary return the pump
to the manufacturer.

20 Undervoltage

Voltage supply < 12 VDC

Check the power supply 24 VDC

21 Overvoltage

Voltage supply > 28 VDC

Check the power supply 24 VDC. The drive
control unit may be damaged. Return the
pump to the manufacturer.

table 29

Problem shooting

If a disturbance that has not been mentioned in the above list, or that makes

the use of the micro annular gear pump unsafe appears, please stop the

operation of the pump without delay and contact HNP Mikrosysteme (see

chapter 13). If needed return the pump to the manufacturer for checkup.

Summary of Contents for mzr-4622





























































































Search results

Summary of Contents for mzr-4622

Reviews:

Related manuals for mzr-4622

Brands by name

Popular brands

HNP Mikrosysteme mzr-4622, Operating Manual

Search results

Summary of Contents for mzr-4622

Reviews:

Related manuals for mzr-4622

Brands by name

Popular brands