HNP Mikrosysteme mzr-4622 Operating Manual Download

Page: 32 / 92

6 System integration

Operation manual mzr-4622

Technical data subject to change without prior notice!

Last update: March 2019

6.3

General instructions for the assembly of the liquid supply network

Foreign bodies and dirt particles can block the micro annular gear pump and

lead to its damage.

Warning

Please note that all the components of the liquid supply system should be

clean and flush them if needed before pump installation. Remember to remove

all remaining splinters or swarf from connection fittings, rests from liquid

containers and any dirt from valves, tubing and filters.

Warning

Operate the pump with a filter featuring 10 µm or smaller pores. The filter

protects the pump from particles and dirt.

If the pump is connected once again with a hose that has already been used,

the enlarged ending of the hose should be cut off in order to prevent it from

slipping off and the liquid from flowing out of the connection.

6.3.1

Assembly of the fluid connection fittings

Cut the hose to a right angle by using an adapted hosecutter.

Warning

Remove the protection caps from the slip fittings of the pump.

If needed, warm up or widen the hose and slip it on the slip fitting till it

touches to the housing.

Pay attention to the correct assembly of the tubing and the pump head in

order to keep the default direction of flow. If you wish to operate the pump in

a reverse direction, please contact one of HNP Mikrosysteme's application

engineers since it is not possible in every case.

The intake tubing should be kept as short as possible and have a possibly

large internal diameter in order to assure best intake performance.

In order to avoid dry operation, check before each use that enough liquid is

supplied to the pump.

Warning

Dry run of the micro annular gear pump may damage in particular the bearing

and the sealing. However, a short dry working phase at the beginning of the

operation is harmless.

6.3.2

Installation with the manifold assembly

Put the pump in the desired position for installation. Ensure that the intake

and the delivery fluid connections have not been inverted.

Warning

Check if the o-ring 1.5 x 1 mm lay correctly and are not damaged.

Screw on the holding nut.

Summary of Contents for mzr-4622





























































































Search results

Summary of Contents for mzr-4622

Reviews:

Related manuals for mzr-4622

Brands by name

Popular brands

HNP Mikrosysteme mzr-4622, Operating Manual

Search results

Summary of Contents for mzr-4622

Reviews:

Related manuals for mzr-4622

Brands by name

Popular brands