HNP Mikrosysteme mzr-4622 Operating Manual Download

Page: 7 / 92

1 General Information

Operation manual mzr-4622

Last update: March 2019

Technical data subject to change without prior notice!

General Information

This operation manual contains basic instructions to be followed during

integration, operation and maintenance of the mzr

micro annular gear pump.

For this reason it is necessary to read it carefully before any handling of the

device. The present manual should always be kept at the operation site of the

micro annular gear pump.

In case assistance is needed, please indicate the pump type visible on the

housing.

1.1

Application scope of the pumps

The micro annular gear pump mzr-4622 described in this manual are suitable

for continuous delivery and discrete dosage of water, watery solutions,

solvents, methanol, oils, lubricating liquids, paints and varnishes as well as

many other liquids.

If you intend to handle any aggressive, poisonous or radioactive liquids, you

must conform to safety measures as according to the regulations in force. Any

project concerning handling of corrosive liquids should be previously discussed

with the pump manufacturer.

The micro annular gear pumps should not be used for "invasive" medical

applications, in which the liquid having had contact with the pump is re-

introduced to the body.

Micro annular gear pumps exclusively are provided for use in the industrial

area. A private use is excluded.

The micro annular gear pumps must not be used in aircrafts and spacecrafts or

other vehicles without prior consent of the manufacturer.

The data concerning resistance of the pumps to manipulated liquids is

elaborated according to the best of HNP Mikrosysteme's knowledge. However,

operating parameters varying from one application case to another, no

warranty for this information can be given.

The information given in this manual does not release the customer from

personal obligation to check the integrity, correct choice and suitability of the

pump for the intended use. The use of the micro annular gear pumps should

be conform with technical norms and regulations in force.

If you wish to receive more information than comprised in this manual please

contact directly HNP Mikrosysteme.

Summary of Contents for mzr-4622





























































































Search results

Summary of Contents for mzr-4622

Reviews:

Related manuals for mzr-4622

Brands by name

Popular brands

HNP Mikrosysteme mzr-4622, Operating Manual

Search results

Summary of Contents for mzr-4622

Reviews:

Related manuals for mzr-4622

Brands by name

Popular brands