HNP Mikrosysteme mzr-4622 Operating Manual Download

Page: 62 / 92

9 »Motion Manager« software (optional)

Operation manual mzr-4622

Technical data subject to change without prior notice!

Last update: March 2019

9.2

Programming of the control unit

The S-ND control unit of the micro annular gear pump may be adapted by the

user to a specific application by means of an easy programming language. The

program files are available in the ASCII code and have by default the »mcl«

extension which stands for "motion controller language". Various parameters

of the drive such as the maximal speed, the acceleration, the number of

rotations to be executed, the allowable current load and the parameters of the

PI-controller may be programmed. Furthermore, it is possible to program short

movement sequences which will be saved in the independent memory of the

drive and then autonomously executed.

A diskette with mcl-programs is included in the delivery and may be saved in

the control unit.

9.3

Transfer of a mcl-file to the drive

The existing mcl-files may be downloaded to the editor window by selecting

File – Open (see figure 35).

figure 35

Menu file- open

The required mcl file may be selected and loaded from the file selection

window (see figure 36).

Summary of Contents for mzr-4622





























































































Search results

Summary of Contents for mzr-4622

Reviews:

Related manuals for mzr-4622

Brands by name

Popular brands

HNP Mikrosysteme mzr-4622, Operating Manual

Search results

Summary of Contents for mzr-4622

Reviews:

Related manuals for mzr-4622

Brands by name

Popular brands