HNP Mikrosysteme mzr-4622 Operating Manual Download

Page: 34 / 92

6 System integration

Operation manual mzr-4622

Technical data subject to change without prior notice!

Last update: March 2019

Warning

Prolonged dry operation of the micro annular gear pump may damage in

particular the bearing and the sealing. However, a short dry working phase at

the beginning of the operation is harmless.

6.4

Filter selection and use

In majority of cases it is recommended to integrate a filter on the suction side

of the micro annular gear pump to ensure its secure operation. The

recommended filter pore or mesh size should not exceed 10 µm. The

penetration of particles or swarf that could cause a blockage or damage to the

pump can only be avoided by using an adapted filter.

HNP Mikrosysteme offers a choice of standard filters covering a broad spectrum

of applications. You may count on our assistance for the selection of the most

suitable filter.

In order to select the best adapted filter, such operating parameters as the flow

rate, the viscosity and the degree of pollution of the liquid will be needed. An

increase in at least one of the mentioned terms will require the use of a bigger

filtering element or pressurization of the delivered liquid. In case no suitable

filter for the given high-viscosity liquid can be found, it is possible to use a filter

with slightly larger pore size. Prior discussion with HNP Mikrosysteme is here

recommended. A filter with larger pores is still better than no filter at all. As an

alternative solution an already filtered liquid may be used.

Warning

Because filters have a large internal volume, it is recommended to fill in the

filter and the induction (suction) tubing with already filtered liquid in order to

avoid a too long dry run of the pump during the first operation.

Warning

Please control regularly the filtering elements for pollution. Cleanse regularly

the filter or replace it with a new one. A polluted filter may considerably

decrease the volumetric efficiency of a pump. Furthermore, because of the

cavitation effects dosage imprecision and even pump damage may occur.

Warning

A too small filter (too little filtering surface) may considerably decrease the

volumetric efficiency of the micro annular gear pump. What is more, because

of the cavitation effects dosage imprecision and even pump damage may

occur.

Summary of Contents for mzr-4622





























































































Search results

Summary of Contents for mzr-4622

Reviews:

Related manuals for mzr-4622

Brands by name

Popular brands

HNP Mikrosysteme mzr-4622, Operating Manual

Search results

Summary of Contents for mzr-4622

Reviews:

Related manuals for mzr-4622

Brands by name

Popular brands