HNP Mikrosysteme mzr-4622 Operating Manual Download

Page: 54 / 92

7 Start Up / Shut Down

Operation manual mzr-4622

Technical data subject to change without prior notice!

Last update: March 2019

7.4.1

Conservation

If the micro annular gear pump operates at irregular intervals or for other

reasons should be put out of operation for a longer period, it should, after

service and flushing procedure (see chapter 7.3), be filled in with a suitable

conservation liquid.

The conservation liquid may be selected from the table 28 depending on the

duration of the standstill and the resistance of the pump to the manipulated

liquid (table 27). The indicated conservation liquids are simple

recommendations and should therefore be checked by the user as to their

compatibility and suitability. The figure 31 presents the diagram of conservation

liquid selection.

Remark

: This diagram is repeated as a part of the figure 30 »Shutdown

procedure«.

After the cleansing procedure the pump should be filled with a suitable

conservation agent. You will find a choice of possible conservation liquids in

the table 28.

Selection of conservation

liquid (CL)

adequate

Is the CL

compatible

with pump

Is the CL

compatible

with the

last FL ?

yes

figure 31

Selection of the conservation liquid (CL)

see table 27 (resistance of the sealing materials)

see table 28 (Selection of conservation liquid)

Summary of Contents for mzr-4622





























































































Search results

Summary of Contents for mzr-4622

Reviews:

Related manuals for mzr-4622

Brands by name

Popular brands

HNP Mikrosysteme mzr-4622, Operating Manual

Search results

Summary of Contents for mzr-4622

Reviews:

Related manuals for mzr-4622

Brands by name

Popular brands