HNP Mikrosysteme mzr-4622 Operating Manual Download

Page: 73 / 92

13 EU Directive

Operation manual mzr-4622

Last update: March 2019

Technical data subject to change without prior notice!

EU Directive

A Directive or EU Directive is a legal instrument of the European Community

addressing at the member states and forcing them to implement specific

regulations or targets. Leastwise, micro annular gear pumps are covered, by the

scope of application of the following Directives: The following directives are of

importance for the user of the described micro annular gear pumps:

Low-Voltage Directive (2014/35/EU)

The Low-Voltage Directive is not relevant for micro annular gear pumps

described in this manual, because the supply voltage is limited to a maximum of

30 VDC.

Machinery Directive (2006/42/EU)

A micro annular gear pump is a machine and is consequently covered by this

Directive. However, it may be a part of a machine or installation.

EMC Directive (2014/30/EU)

The Directive on Electromagnetic Compatibility (EMC) applies to all electronic

and electrical devices, installations and systems. Consequently, the Motion

Controller of the micro annular gear pump is covered by the EMC Directive.

RoHS Directive

(

2011/65/EU)

To our knowledge our products delivered to you do not contain substances or

applications in concentrations that are forbidden by this directive. No

substances contain our products delivered to you after our current knowledge

in concentrations or application, the placing on the market in products

according to the valid requirements forbade to the Directive.

WEEE Directive (2002/96/EU)

Disposal of micro annular gear pumps has to be environmentally sound.
All materials and liquids haveto be recycled in accordance with the relevant

regulations. Electrical parts can not be disposed of as household waste. They

have to be delivered to designated collection points.

Summary of Contents for mzr-4622





























































































Search results

Summary of Contents for mzr-4622

Reviews:

Related manuals for mzr-4622

Brands by name

Popular brands

HNP Mikrosysteme mzr-4622, Operating Manual

Search results

Summary of Contents for mzr-4622

Reviews:

Related manuals for mzr-4622

Brands by name

Popular brands