Hitachi PSC-A128WEB3 Operation Manual Download Page 69

Page: 69 / 76

P5416904

No.

Event

Items to be checked

Action

6 Even if this system is

in Run command,

the Air conditioner

does not run.

Check that there is no error

between the Computer and this

system connection.

Check if the LAN cable is wired correctly and if

the HUB and this system power is turned ON.

Check if the Alarms 60, 61, 64

and 65 are ON.

A communication error has occurred in H-LINK.

Check if the power of the Air conditioner is not

OFF, check H-LINK wiring and transmission

status.

Is the air conditioning unit in

[Stop] or in [Emergency Stop]

mode depending on the External

input of this unit?

Deactivate the External Input Signal.

Is the RC group correctly

registered?

RC groups must be allocated to one group

number between

“1-160”. If “O” is shown, allocate one number

from “1-160”.

Did the connection of the RC

change such as in

the removal of the RC?

To modify the connection to the RC, execute it

while the power to the AC is OFF.

If the modification is performed while the AC

is ON, turn the power OFF once, then turn the

power back ON.

Then click [Check connection] in [Settings] >

[Unit register] of the management software.

Is Stop Signal depending on the

External input in the Indoor unit

is ON?

The halt depending on the External Input Signal

inputed in the Indoor unit is taking priority.

Deactivate the External Input Signal.

Is there a time setting

discrepancy between the Unit

and the computer?

The displayed time in the

lower right hand corner of the

applications user interface

should match the current time on

the PC.

Set the time of this unit following the

Preparation for Setup of this manual [the item

of (9) of

Power supply (page 11)].

Even operating from

this system,

it will stop after a

certain time.

Did the connection of the RC

change, such as in the removal of

the RC?

To modify the connection to the RC, execute it

while the power to the AC is OFF.

If the modification is performed while the AC

is ON, turn the power OFF once, then turn the

power back ON.

Then click [Settings] > [Unit register] of the

management application and recheck the

connection.

8 Certain units are not

operating even in [On

all].

Does [On all] have any effect on

the unit?

Select the item for [All prohibited] in Control

Panels as [None] or [OFF].

9 Certain units are not

stopping even in [Off

all].

Does [Off all] have any effect on

the unit?

Select the item for [All prohibited] in Control

Panels as [None] or [ON].

Summary of Contents for PSC-A128WEB3













































































Search results

Summary of Contents for PSC-A128WEB3

Reviews:

Related manuals for PSC-A128WEB3

Brands by name

Popular brands

Hitachi PSC-A128WEB3, Operation Manual

Search results

Summary of Contents for PSC-A128WEB3

Reviews:

Related manuals for PSC-A128WEB3

Brands by name

Popular brands