Hitachi PSC-A128WEB3 Operation Manual Download

Page: 21 / 76

P5416904

Initial Setting

Maintenance Mode

Management Mode

Language setting

Setting language for display. This setting can be used in English and French version.

(1) Go to [Settings] - [Language] to set language for display.

1. Choose language.

2. Click [Done].

NOTE:

● When utilizing this unit from plural computers, unify all settings of language.

● If choosing to keep registered name data, some characters (depending on locale and language) may not

be displayed correctly.

● When choosing to delete registered data, the followings will be deleted.

Names of IDU, Schedule operating pattern, Specific day, Information about RC Group, Group and Block

(2) Choose to keep registered name data or to delete registered data.

(3) Management system will close automatically.

Set the following items as necessary.

②

①

Summary of Contents for PSC-A128WEB3













































































Search results

Summary of Contents for PSC-A128WEB3

Reviews:

Related manuals for PSC-A128WEB3

Brands by name

Popular brands

Hitachi PSC-A128WEB3, Operation Manual

Search results

Summary of Contents for PSC-A128WEB3

Reviews:

Related manuals for PSC-A128WEB3

Brands by name

Popular brands