Hitachi PSC-A128WEB3 Operation Manual Download

Page: 65 / 76

P5416904

Display Alarm History

Maintenance Mode

Management Mode

Control Mode

Monitoring Mode

1 Display

■ The Alarm history recorded in this system can be shown in a list.

Up to 500 alarms can be recorded in this system. When the number of recorded alarms exceeds 500, the oldest

alarm recorded is deleted to create space for a new alarm record.

Display

Display [All] and select the [Block] and the [Group]

that are set.

Alarm History

When an alarm is generated, the alarm number (No.), the date of the alarm (Date),

the time it occurred (Time), the alarm code (Code), the alarm content (Content), Block

name, Group name, Unit name, System and Address will be displayed.

Mode Switch

Used to change the

page of the Alarm

history (UP/DOWN).

To print out the Alarm

History.

Update

To display the latest alarm

generated.

Status Bar

When an alarm is generated, the status bar is shown in Red

and the Unit name, Refrigerant system, No. and Alarm Code are

displayed.

Delete history

Used to delete the

entire Alarm History.

NOTE:
Even when the history is deleted, until the new alarm is generated and the record updated, the history

before deletion will remain within the non-volatile memory of this system. When this system is restarted

because of a power failure, the history before deletion which remains in the non-volatile memory will be

restored.

However, if restarting after performing the Network setting, the content of the history before deletion is

updated and will restart.

Summary of Contents for PSC-A128WEB3













































































Search results

Summary of Contents for PSC-A128WEB3

Reviews:

Related manuals for PSC-A128WEB3

Brands by name

Popular brands

Hitachi PSC-A128WEB3, Operation Manual

Search results

Summary of Contents for PSC-A128WEB3

Reviews:

Related manuals for PSC-A128WEB3

Brands by name

Popular brands