Hirschmann OZD Genius G12-1300 User Manual Download Page 8 | Manualshive

Page: 8 / 72

background image

8

Installation OZD Profi 12M ...

Release 01 07/2017



CE marking

The labeled devices comply with the regulations contained in the following
European directive(s):

2014/30/EU (EMC)
Directive of the European Parliament and the council for standardizing the
regulations of member states with regard to electromagnetic
compatibility.

2011/65/EU (RoHS)
Directive of the European Parliament and of the Council on the restriction
of the use of certain hazardous substances in electrical and electronic
equipment.

In accordance with the above-named EU directive(s), the EU conformity
declaration will be at the disposal of the relevant authorities at the
following address:

Hirschmann Automation and Control GmbH
Stuttgarter Str. 45-51
72654 Neckartenzlingen
Germany

The product can be used in the industrial sector.



Interference immunity: EN 61000-6-2



Emitted interference: EN 55032



Reliability: EN 60950-1

You find more information on technical standards here:

“Technical data” on page 57

Warning!

This is a class A device. This device can cause interference in

living areas, and in this case the operator may be required to take
appropriate measures.

Note:

The assembly guidelines provided in these instructions must be

strictly adhered to in order to observe the EMC threshold values.



LED or laser components

LED or LASER components according to IEC 60825-1 (2014):
CLASS 1 LASER PRODUCT
CLASS 1 LED PRODUCT

«
...
6
7
8
9
10
...
»

Summary of Contents for OZD Genius G12-1300









































































Reviews:

No comments

Related manuals for OZD Genius G12-1300

Brand: Lasko Pages: 4

Brand: Icom Pages: 16

IC-FR4000 Series

Brand: Icom Pages: 20

Brand: Radialight Pages: 10

Brand: Lasko Pages: 4

Brand: R-tron Pages: 20

Brand: Frico Pages: 6

Brand: Toyostove Pages: 18

Brand: Olimpia splendid Pages: 52

Brand: PARAGON OUTDOOR Pages: 19

Brand: Twin-Star International Pages: 12

Brand: IVIGO Pages: 52

Brand: COMFORT-AIRE Pages: 8

Eco Heater HHT060

Brand: hylite Pages: 16

Brand: SIIG Pages: 11

Brand: Digisol Pages: 12

Brand: Gabarron Pages: 4

Brand: Flagro Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands