manualshive.com logo in svg

Hirschmann OZD Genius G12-1300, User Manual, Page: 32 / 72

Share
Download
Hirschmann OZD Genius G12-1300 User Manual Download Page 32

32

Installation OZD Profi 12M ...

Release 01 07/2017

3

Installation guidelines

3.1

Electromagnetic compatibility (EMC)

Electromagnetic compatibility (EMC) covers all aspects regarding the effects 
of radiated and received electrical, magnetic, and electromagnetic 
emissions. In order to prevent interference in electrical systems, these 
effects must be reduced to a minimum. The structural design and correct 
connection of bus lines as well as the interference suppression of switched 
inductances play a major role in limiting interference.

3.2

Interference suppression of switched 

inductances

Figure 4: Interference suppression of fluorescent lamps in cabinet

3.2.1

Suppressing switched inductances with fuses

Switching inductances, e.g. in relays and fans, generates interference 
voltages which are many times higher than the switched operating voltage. 
These interference voltages can affect electronic devices. The interference 
voltages of inductances must be limited at their source of emission by means 
of fuses (by connecting diodes or RC elements). Only use interference 
suppressors which are intended for the used relays and fans.

3.2.2

Cabinet lighting

Use filament lamps (e.g. LINESTRA lamps) for the cabinet lighting.

Do not use fluorescent lamps because they generate interference fields. 
If the use of fluorescent lamps cannot be avoided, the interference 
suppression measures shown in Fig. 4 must be implemented.

Shield grid 
over lamp

Shielded cable

Metal-encased 
switch

Mains filter or 
shielded mains cable

Summary of Contents for OZD Genius G12-1300









































































Reviews:

No comments