Hirschmann OZD Genius G12-1300 User Manual Download Page 62

Page: 62 / 72

Installation OZD Profi 12M ...

Release 01 07/2017

Underlying technical standards

The device has an approval based on a specific standard only if the approval
indicator appears on the device casing.
The device generally fulfills the technical standards named in their current
versions.

Name

CSA C22.2 No. 142

Canadian National Standard(s) – Process Control Equipment –
Industrial Products

FCC 47 CFR Part 15

Code of Federal Regulations

UL/IEC 61010-1,
UL/IEC 61010-2-201

Safety for Control Equipment

EN 55022

Information technology equipment – Radio disturbance
characteristics – Limits and methods of measurement

EN 55032

Electromagnetic compatibility of multimedia equipment.

EN 61000-3-2

Electromagnetic compatibility (EMC) - Part 3-2: Limits - Limits for
harmonic current emissions

EN 61000-3-3

Electromagnetic compatibility (EMC) - Part 3-3: Limits - Limitation
of voltage changes, voltage fluctuations and flicker.

EN 61000-6-2

Electromagnetic compatibility (EMC) – Part 6-2: Generic
standards – Immunity for industrial environments

EN 61000-6-4

Electromagnetic compatibility (EMC) – Part 6-4: Generic
standards – Emission standard for industrial environments

EN 61131-2

Programmable controllers – Part 2: Equipment requirements and
tests

Table 10: List of the technical standards

Summary of Contents for OZD Genius G12-1300









































































Search results

Summary of Contents for OZD Genius G12-1300

Reviews:

Related manuals for OZD Genius G12-1300

Brands by name

Popular brands

Hirschmann OZD Genius G12-1300, User Manual

Search results

Summary of Contents for OZD Genius G12-1300

Reviews:

Related manuals for OZD Genius G12-1300

Brands by name

Popular brands