Hirschmann OZD Genius G12-1300 User Manual Download Page 9 | Manualshive

Page: 9 / 72

background image

Installation OZD Profi 12M ...

Release 01 07/2017

9



FCC note:

This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference; (2) this device must accept any interference received,
including interference that may cause undesired operation.
Appropriate testing has established that this device fulfills the
requirements of a class A digital device in line with part 15 of the FCC
regulations.
These requirements are designed to provide sufficient protection against
interference when the device is being used in a business environment.
The device creates and uses high frequencies and can also radiate these
frequencies. If it is not installed and used in accordance with this
operating manual, it can cause radio transmission interference. The use
of this device in a residential area can also cause interference, and in this
case the user is obliged to cover the costs of removing the interference.



Recycling note

After usage, this device must be disposed of properly as electronic waste,
in accordance with the current disposal regulations of your county, state,
and country.

«
...
7
8
9
10
11
...
»

Summary of Contents for OZD Genius G12-1300









































































Reviews:

No comments

Related manuals for OZD Genius G12-1300

Brand: ARDES Pages: 16

ULTRASlimline 10222

Brand: Seville Classics Pages: 6

Brand: Delta Thermie Pages: 21

Brand: Inelco Pages: 23

Brand: Mark Pages: 80

WEXT5-SRCOOL12K

Brand: Tripp Lite Pages: 2

Repeater Translator RE220T

Brand: Resolution Products Pages: 2

Brand: Niko Pages: 8

Brand: MrHeater Pages: 8

Brand: R-tron Pages: 41

Brand: Myson Pages: 12

Brand: GVA Pages: 7

Compact Wi-Fi Repeater

Brand: Anker Pages: 22

Brand: Klarstein Pages: 32

Brand: Klarstein Pages: 40

Brand: Klarstein Pages: 60

Brand: Klarstein Pages: 74

Brand: Klarstein Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands