Hirschmann OZD Genius G12-1300 User Manual Download Page 38

Page: 38 / 72

Installation OZD Profi 12M ...

Release 01 07/2017

Installation

The devices have been developed for practical application in a harsh
industrial environment.
Hirschmann supplies the device ready for operation.

To configure a subdomain, follow these steps:



Checking the package contents



Mounting the device



Setting compatibility



Connecting the optic bus cables



Connecting the electric bus cables



Connecting the function ground and the shield of the bus cable



Connecting the power supply



Connecting the signal contact (optional)



Connecting the analog voltage outputs (optional)

4.1

Checking the package contents

Proceed as follows:



Check whether the package includes all items named in the section

“Scope of delivery” on page 61



Check the individual parts for transport damage.

Summary of Contents for OZD Genius G12-1300









































































Search results

Summary of Contents for OZD Genius G12-1300

Reviews:

Related manuals for OZD Genius G12-1300

Brands by name

Popular brands

Hirschmann OZD Genius G12-1300, User Manual

Search results

Summary of Contents for OZD Genius G12-1300

Reviews:

Related manuals for OZD Genius G12-1300

Brands by name

Popular brands