manualshive.com logo in svg

HIOS HSV-10RB, Instruction Manual, Page: 28 / 36

Share
Download
HIOS HSV-10RB Instruction Manual Download Page 28

- 27 -

Trouble

Cause

Corrective measures

9-3
A screw has fallen into the rail groove.

・

Screws with a smaller diameter than the 

specified rail size were loaded.

・

Screws with a shorter total length than 

the rail groove width were loaded.

・

Use screws with the specified nominal 

diameter and length.

・

No corrective measure is available.

   Consult our service section.

9-4

The flow on the screw rail is improper.

・

The clearance between the holding plate 

and the head of the loaded screw is too 
low.

・

 Screws with a spring washer having one 

increment smaller than the specified 
nominal rail size were loaded.

・

The rail is oily or dirty.

・

The rail does not vibrate.

 (A screw is caught in the clearance.)

・

The motor is worn.

・

Adjust the holding plate bracket assem-

bly. (Adjust the holding plate.)
Adjust the vibration.

If, after following the instructions written 
above, the machine still does not function 
properly, consult our service section.

・

Clean the rail.

・

Remove the screws caught in the clear-

ance. 
If there is no screw that is caught, consult 
our service section.

・

Check that the vibration level is properly 

adjusted.

・

Replace the motor.

      [Part No: HSVRB-09105-15]

Summary of Contents for HSV-10RB





































Reviews:

No comments