manualshive.com logo in svg

HIOS HSV-10RB, Instruction Manual, Page: 27 / 36

Share
Download
HIOS HSV-10RB Instruction Manual Download Page 27

- 26 -

Trouble

Cause

Corrective measures

9-2 

Screws do not flow.

・

Screws in an abnormal position in the 

passing plate cannot be swept away with 
the brush.

・

The axis of the screw thread entered the 

passing plate.

・

A screw has stopped in an abnormal po-

sition while moving on the rail.

・

The rail does not vibrate.

  (For example, a screw is obstructing the 

clearance.)

・

Adjust the brush.

Adjust the passing plate.
If a proper amount of screws are loaded 
into the scooping chamber the status may 
be improved.
Use the optional brush. (stiffer bristles)

     [Parts No: HS3-02110-2]

・

Remove the abnormal screw and check 

and adjust the passing plate.

 

・

 Remove the screw in the abnormal posi-

tion. Take care not to damage the rail 
groove.

  Move the holding plate bracket assembly 

upward to remove the screw. After, adjust 
the position of the holding plate. 

・

Remove the screw that is obstructing the 

clearance.

・

 Check the vibration adjustment.

  If no screw is obstructing the clearance, 

consult our service section.

Summary of Contents for HSV-10RB





































Reviews:

No comments