manualshive.com logo in svg

HIOS HSV-10RB, Instruction Manual, Page: 21 / 36

Share
Download
HIOS HSV-10RB Instruction Manual Download Page 21

Remove the rear cover of the machine. While adjusting 
the sensor, check the voltage of  No.7 pin of IC4050. 

 No.7 pin of IC4050

１

2

①

Push the sensor bracket down and check if the voltage 

is more than 4V.

② 

Move the sensor bracket up slowly to reach a voltage of 

between 0.25V-1.5V.

Sensor bracket

Location of the 
sensor bracket 
attaching bolts

This is no malfunction when the 
voltage is slightly off of 2.5V.
The adjustment, for ordinary screws, 
would be as described above.

For screws which have a flatter 

head, refer to the figure on the left 

for adjustments.
Depending on the screw-head 
height, it may be necessary to 
set the low-range voltage at more 
than1.5V and the high-range volatge 
at under 3.5V.

5V

4V

3V

2V

1V

0V

  2.5V

Voltage
when there is
a screw.

Under 1.5V
The recommended 
voltage for when 
there are no 
screws.

High

Low

The 
recommended 
voltage is over 3.5V
when the screw is 
in position.

- 20 -

Voltage
when there is
no screw.

⑤. 

Checking and adjusting the sensor

Check when required.

When checking is required, take the rear cover off and check the volt

-

age level of No.7 pin of IC4050 on the base and adjust the sensor 
bracket. When measuring the voltage level, the metal part of the main 
body is the ground. 

When a screw is not at the extraction site, turn the power ON.  
Next loosen the 2 sensor bracket attaching bolts and do the following:  

①. 

Move the sensor bracket down and check if the voltage is over 4V and if 

the sensor light is ON.  At this time, the escaper is stopped. 

②. 

Next, while checking the voltage level, slowly move the sensor bracket up 

which causes the voltage to decrease. When the voltage is around 0.25V-
1.5Vtighten the sensor bracket. During this procedure when the voltage is 
around 2.5V, the LED screw sensor turns OFF and the escaper rotates. 

 

      

When there is no screw at the extraction site, the voltage is 0.25V-1.5V 
and the LED screw sensor is OFF.  
When there is a screw at the extraction site and the voltage is over 
3.5V, the LED screw sensor is ON. This is a general standard. 
The borderline, if there is a screw in position or not, is 2.5V.

Summary of Contents for HSV-10RB





































Reviews:

No comments